Before using any lifting equipment, it is important to perform a proper inspection. This includes checking the condition of the lift and its components, verifying that all safety features are in working order, and ensuring that the operator is qualified to operate the equipment safely.
Below you’ll find a complete lifting equipment inspection checklist that can help you properly check everything before starting work.
Uneven loads & loads greater than 1 tonne must be slung by or under the instruction of a qualified rigger or dogman
All commercial-grade equipment must clearly display the Working Load Limit (WLL) Lifting equipment should be inspected annually by an accredited tester Do not use out-of-test equipment Do not overload components Overloading of components Failure of components In-service failure Damage to equipment Damage to load Incompatibility of parts Detachment from load Detachment from a crane hook Loss of control of loadEnsure lifting gear & slings conform to the relevant Australian Standards or other prescribed Standard
Engage a qualified rigger or dogman to sling uneven loads & loads greater than 1 tonne Ensure all commercial grade equipment clearly displays the working load limit (WLL)Commercial lifting equipment will carry either the Working Load Limit (WLL) or the grade of the material
Commercial fittings will not be compatible with other fittings. Equipment not labeled with WWL or Grade must not be used
Check that lifting load gear will safely carry the proposed loadCheck load charts or load plates on sets & legs of multi-leg sling sets or objects being lifted do not exceed the allowable load
Ensure all equipment has the same WWL to maintain correct Clarence & prevent overloading & components
Use soft packing to protect corners, or use synthetic flexible slings to lift angular or "soft" loads
Use correct hooks to ensure the load or part of the lifting tackle will be secure & will not separate, loosen or dislodge during lifting
Ensure safety hooks & fittings are approved Inspection Lifting equipment should be inspected daily before useVisibility inspects wire ropes for evidence of wear, damage, broken wires, or kinks. Discard if more than 10% of wires are broken in length equal to Dia x 8
Inspect swayed fittings & thimbles & discard if damaged Visually inspect slings before use Check covers of round slings for wear, burns, or cuts. Check load indicators Inspect webbing slings for cuts, wear or stretching; check eyes and stitching Keep slings clean to prevent grit from damaging the fabric Remove faulty slings and sets from service and repairs or destroy Inspect chains & fittings for cracks, wear, damage or distortion All repairs should be carried out by a competent personSlings and sets used on construction and high-risk work, or hired out with cranes, must be inspected and tested annually by a NATA accredited testing facility
Ensure a current testing tag is fitted Terminal Fittings Inspect hooks & fittings for wear, cracks, damage & distortionKeep fittings lightly oiled to maintain movement & prevent corrosion. Wipe off excess oil with a dry cloth
Hired out Equipment Ensure slings and sets are clearly marked with WWL and load plates Ensure that sling carry a current test tag Inspect slings, sets and fittings before and after each hire Ensure that slings and sets are suitable for the mass and type of proposed loads Provide protection for slings Check load charts to ensure that lifting equipment is not overloaded Ensure that lifting equipment and components are compatibleUse positive closure fittings such as shackles and safety-latch hooks to ensure the load is securely attached
Check that legs of chain sling sets are not twisted, as untwisting can cause ring to roll onto hook latch and detach
Do not put a sling out from under the load and surface. Do not allow a sling to settle between load and surface
Do not pull sling out from under a load by mechanical means Keep equipment clean from dirt to maintain the integrity of the sling Wear suitable gloves to protect hands from broken wires and rough edges when handling slingsAvoid exposing lifting equipment to saltwater, heat, corrosives, or and another element that will cause damage
Do not drive vehicles over slings, chains, ropes, or fittings Wear gloves when handling wire ropes to prevent hand injury Completion Thoroughly clean slings and fittings after use Ensure all worn or faulty fittings are replaced by a competent person with compatible fittings Check WWL of all components Provide secure clean storage for lifting equipment Always hang slings and chainsets from pegs, enabling them to hang straight No Signature/No Start Add Signature Add Signature Add Signature Share this template:One of the most crucial items of equipment utilised on construction, industrial, and other work sites around the world is lifting equipment. Ensure the safe operation of your lifting equipment is to having an inspection checklist in place. This will help you identify any problems with the equipment, and ensure that it is working properly before each use. This lifting gear inspection checklist comes with a proven and reliable framework, with sections for the use of the equipment, suitability of the equipment, positioning and installation (if necessary), as well as more. It’s essential that you have the proper documentation of your lifting gear inspections available at all times so that any issues can be addressed quickly and safely.
To ensure a safe and effective lifting equipment inspection, follow these simple guidelines:
Please note that this checklist template is a hypothetical appuses-hero example and provides only standard information. The template does not aim to replace, among other things, workplace, health and safety advice, medical advice, diagnosis or treatment, or any other applicable law. You should seek your professional advice to determine whether the use of such a checklist is appropriate in your workplace or jurisdiction.